China brass wire drawing low maintenance device Manufacturers Factory Suppliers
We firmly believe that this brass wire drawing maintenance tool, brass wire drawing display quality device, wire drawing machine for brass industry is full of potential and infinite possibilities in the face of challenges.Our company is a brass wire drawing low-maintenance device full-industry service complex with the largest volume, the most complete format, the most complete supporting facilities, and the most development potential. Our company is well-equipped to handle large and small orders alike. Our team of experts has the knowledge, skills, and experience needed to provide top-quality products and services to our clients. We hope to save every social resource from within the enterprise and devote ourselves to the construction of energy-saving enterprises with practical actions. Till now, the company has become an indispensable force in promoting social and economic development. Over the years, under the strong leadership and care and support of the group, the company has implemented the group's "one responsibility, three changes" management system of "work proceduralization, quality standardization, and behavior standardization with the economic target responsibility system as the core"
Add to Inquiry
Intermediate Wire Drawing Machine
Intermediate Wire Drawing Machine is used for drawing and annealing pure copper wire, followed by online annealing. Both single wire and two wires are available for choose.
Add to Inquiry
Fine Wire Drawing Machine with Continuous Annealing
The voltage automatically tracks the drawing speed, so it can ensure the wire performance at the same rate during speed up or speed down.
Add to Inquiry
Wire Annealing Machine
Wire Annealing Machine is special for annealing 40 copper wires or CCS Wire 0.15-0.70 mm at the same time. Finished wire is wound by plastic bobbin.
Add to Inquiry
EDM Wire Drawing Machine
EDM Wire Drawing Machine is special used for drawing and annealing copper or brass wire to 0.07-0.20 mm. Finished wire is wound by 300 steel bobbin or similar size plastic bobbin.
Add to Inquiry
Brass Wire Annealer
Brass Wire Annealer is special for annealing 40 copper wires 0.08-0.32 mm at the same time. The annealing body length of the brass wire annealer is 4.5m. The water tank is re-cycle design and with
Add to Inquiry
Brass Annealing Machine
Brass Annealing machine is special for annealing 32 copper wires 0.03-0.08 mm at the same time. Finished wire is wound by plastic bobbin. The water tank is re-cycle design and with water tank and
Add to Inquiry
Rod Breakdown Machine
In this way, it is possible to reduce or avoid the squeezing and scratches between the wire wound on the drum during the wire drawing process.
Add to Inquiry
Rod Breakdown Drawing Machine
The specially designed ventilation duct is used to send air to the rear of the annealing wheel, cooling the annealing carbon brush and the wheel axle.
Add to Inquiry
EDM Brass Wire Drawing Machine
The four dies before the outlet die can be adjusted for straightness and the final outlet die holder is three-dimensional adjustable,it can be easy to adjusted and has a good stability.
Add to Inquiry
Drawing Machine for Brass Wire
Traversing was controlled by 110W belt-type synchronous motor, stable and fast response. Linear bearings are slide rails, with high rigidity and low wear.
Add to Inquiry
Electric Wire Drawing Machine
Electric Wire Drawing Machine body is welded structure by the steel plate with annealing progress.There are six or ten layers for drawing capstan with horizontal structure.
The details of these products are very good and I am very satisfied.
Your experience in the industry is unmatched, and you have always kept up with the trend and been a trendsetter of the times!
Everything in this purchase is packaged in perfect condition, and the logistics are very fast. If we have similar needs in the future, we will give them a priority.
From product drawing design, material selection, and automated production to product quality inspection, they are all done very rigorously, and the schedule is also very reasonable.
"Scientific development, lasting innovation" is synonymous with you, and it is really good that you will learn from the excellence of your peers.
Arrived quickly and the quality is good, I will recommend it to my friends~
Our company adheres to the brand concept of "dedicated to healthy products", forging quality Wire Drawing Machine Accessories, high-speed wire drawing machine leading the development of the industry, and has now developed into a comprehensive group focusing on Copper Fine Wire Drawing Machine, EDM Brass Wire Drawing Machine, Double Twist Machine products. As one of the leading brass wire drawing low-maintenance device manufacturers and suppliers in China, we warmly welcome you to buy high-grade brass wire drawing low-maintenance device for sale here from our factory. All customized products made in China are with high quality and competitive price. Contact us for pricelist.

















